DMG Luxabond Dual Curing
Bonding Agent
LuxaBond-Total
Etch is a dual-cure bonding agent for enamel and dentin, suitable for use with
dual-cure and self-cure composites, such as LuxaCore Z-Dual. It is necessary to
etch enamel and dentin surfaces prior to application. Due to the dual-cure
nature of the material, LuxaBond-Total Etch is particularly useful when
bond-ing posts in areas where light can’t penetrate.
FEATURES :-
- Compatible with all composite resin
materials - recommended for all applications with LuxaCore.
- Indicated for bonding of posts,
cores, crowns, bridges, inlays and onlays.
- Cures without a light; can be used
for all indirect procedures.
- Better adhesion.
- Specifically shaped Endobrushes
for an easier application in the root canal.
- Non-acetone, non-alcohol
formulation.
COMPOSITION :-
- Pre-bond: Ethanolic aryl sulfonate
solution.
- Bond A: Hydrophilic Bis-GMA based
resin matrix, catalyst.
- Bond B: Hydrophilic Bis-GMA based
resin matrix, benzoyl peroxide.
INDICATIONS :-
- Used in conjunction with total
etch technique for core build ups and addition of resin cements for posts,
crowns, bridges, inlays & onlays.
SPECIFICATIONS :-
- Working time of the mixture of
bond A + bond B (storage in a dark place) : 5 min.
- Reaction time of the etching gel
to enamel : 20 to 60 s.
- Reaction time of the etching gel
to dentin max.: 15 s.
- Pre-bond work-in time : 15 s.
- Mixing time of bond A + bond B : 5
s.
- Bond A + bond B work-in time : 20
s.
- LuxaBond-Total Etch exposure time min.
: 10 s.
DIRECTIONS TO USE :-
- Prepare the root canal or cavity
in accordance with the general rules for adhesive procedures. We recommend
the use of a rubber dam.
- Etch dentin and enamel with 37 %
phosphoric acid gel or similar. Start the etching process with the enamel
and then expand this to include the dentin. The reaction time on the
enamel should be 20 to 60 s. The reaction time on the dentin must not
exceed15 s.
- Please note: When using
LuxaBond-Total Etch it is essential to etch the affected enamel and dentin
surfaces.
- Rinse with water for a minimum of
15 seconds.
- Remove general water excess. After
the rinsing process, an even moist layer must remain on the dentin surface
requiring treatment. If necessary, wet the dentin surface using a lightly
moistened micro brush.
- Use a brush to work 1 to 2 drops
of pre-bond into the etched tooth structure for 15 s. Remove any excess,
e.g. with a paper tip. Blow gently using oil and water-free air. The
surface should appear evenly moist.
- Mix 1 to 2 drops of bond A and
bond B in a trough in the mixing palette at a ratio of 1:1 for approx. 5 s
and work into the tooth structure for 20 s using a micro brush.
- Carefully remove bond excess from
the preparation, e.g. with a paper tip, and then gently blow with oil and
water-free air until the surface appears evenly
- moist.
- Apply the attaching cement in
accordance with the manufacturer’s instructions.
CONTENTS :-
- 5ml bottle Pre-Bond
- 5ml bottle Bond A
- 5ml bottle Bond B
- 2ml syringe Etch Gel Medium
Viscosity
- 25 red Endobrushes
- 25 Black Endobrushes
- 3 Luer-lock Tips
- 1 mixing palette
dental extraction
dental equipments
dental emergency
dental excellence
dental essence
dental erosion
dental emergency drugs
dental expertz
dental esthetics
dental explorer
dental elevators
dental expo 2019
dental education posters
dental equipment online
dental elegance
dental enamel
dental exam
dental extraction forceps
Subscribe by Email
Follow Updates Articles from This Blog via Email
No Comments